







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Trusted Fence Installation for Kendall Homeowners
Kendall lots tend to be wide and shallow, and many back onto the canals and drainage easements that run through the western neighborhoods. That layout creates two problems at once: side-yard fences hit a setback or utility line you didn’t plan for, and a chain link fence that sat in wet ground for years is often leaning well before the homeowner notices. Fence installation in Kendall works when the installer checks the property line, the setback, and the soil before anyone sets a post. Our technicians have up to 14 years of experience with wood, vinyl, aluminum, chain link, and iron fencing, and we work with licensed and insured independent local professionals who measure before they quote. Call (888) 300-8968 for a free estimate.

Key Takeaways
- Typical vinyl fence installation in Kendall is estimated at $3,500 – $9,000; aluminum runs $4,000 – $10,000. The written estimate sets the final price.
- Setbacks, utility easements, and canal-adjacent soil conditions drive more fence problems in Kendall than materials do.
- Estimates are free, line-item, and fixed, with no change orders once work starts.
- Our team specifies Master Halco and Ameristar fencing systems where the material choice matters for durability.
What Our Fence Installation Service Includes

Wood Fence
Wood fencing is the most common choice for enclosing a Kendall backyard, and it’s the material most sensitive to ground moisture. If a crew sets pressure-treated posts in soil that stays damp, the fence will start to rack and lean within a few seasons. We specify the post depth and concrete footing for the conditions on your lot rather than using a one-size depth, and we talk through board spacing so the fence breathes in humid weather. Wood is the right call when you want privacy, a natural look against the landscaping, and the ability to repair a section later without replacing the run.
Chain Link Fence
Chain link is the practical choice for side yards, dog runs, and property lines where visibility isn’t a concern. It’s also the fence most Kendall homeowners inherit from a previous owner, which means it’s often sagging at the posts, rusting at the fabric, or missing tension wire. We assess whether the existing posts can be reused before recommending a full replacement, since a sound post line can save a meaningful part of the cost. When we do install new chain link, we set the terminal posts, tension wire, and gate hardware so the fabric stays tight.
Vinyl Fence
Vinyl fencing holds its color and needs no painting, which makes it a strong fit for Kendall’s humidity and sun exposure. It’s the material we install most for privacy runs, and the price range for a typical job starts around $3,500. The part that matters on installation is the post, not the panel: vinyl panels are rigid, so a post set too shallow or too loose will show how much it flexes at the first good wind. We install with reinforced posts and the correct concrete footing to match the height of the run.
Aluminum Fence
Aluminum fencing gives you the look of wrought iron without the maintenance, and it’s powder-coated so it doesn’t rust through in wet weather. Homeowners choose it for pool enclosures, front property lines, and anywhere they want to see the landscaping rather than block it. Aluminum installation runs higher than vinyl, typically starting around $4,000, because the panels and pickets are specified by grade and spacing. We build Ameristar aluminum systems where the project calls for a clean, consistent picket line and a gate that swings true.
Iron Fence
Iron fencing is the classic security and curb-appeal option, and it’s what most people picture when they describe a stately front yard. Iron is heavier than aluminum, needs periodic attention to its coating, and requires solid, well-set posts to carry the weight of the panels. It’s the right fence when you want something that lasts and reads as permanent. We install iron fencing with gate hardware sized to the weight and confirm hinge and latch placement so the gate doesn’t sag.
Fence Repair
Not every fence needs replacing, and part of a good installation service is knowing the difference. A single leaning post, a broken picket, a gate that won’t latch, or fabric that’s pulled loose at the bottom can often be repaired for a fraction of a new run. We inspect the whole line for the underlying cause, because a fence that leans in one spot usually has a reason, and repairing the symptom alone gets you back on the phone next season. If the damage is broader than one section, we’ll tell you plainly and give you both an option.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Brands We Service for Fence Installation
We install Master Halco fencing systems, and our experience with that line runs across the vinyl and ornamental products where post quality and hardware compatibility decide how a fence ages. Knowing how Master Halco components fit together matters on repair jobs, where a homeowner wants a matching section rather than a visibly mismatched panel. We also work with Ameristar aluminum and steel fencing, which is the material we specify when a project needs a consistent picket profile and a gate that stays level over time.
Bufftech vinyl fencing comes up often on privacy runs, and we know which profiles work best in the sun and moisture conditions here and where the post reinforcement needs to be upgraded. Jerith ornamental fencing is another line we install when the project calls for a traditional iron look with a factory finish. Whether your project involves one of these brands or any other make, we can help you choose the right specification and set it correctly.
Signs You Need Fence Installation Right Now
- Posts that lean after rain. A fence that wobbles at the post is usually sitting in ground that holds water. It’s the earliest sign the footing wasn’t set deep enough, and waiting lets the whole run rack out of line.
- Rot at the base of wood boards. Wood that’s soft at the bottom, or breaks away when you press it, is past the point where painting helps. Replacing the boards without addressing the post usually means the fence fails again in the same spot.
- Rust bleeding down the panels. Rust streaks on chain link or iron mean the coating has failed, and the metal underneath is thinning. It’s cosmetic at first but structural once the wire or the joints start to open up.
- A gate that drags or won’t latch. A gate that catches on the ground or has to be lifted to close is a sign the post or hinge has moved. It’s a small repair now and a security gap later.
- Panels that flex in wind. Vinyl and aluminum panels moving more than they should tells you the posts are undersized or too shallow for the height of the run. Fixing it before a storm is far cheaper than fixing it after.
Our Fence Installation Process – Step by Step
- 1
Property line and setback review. We start by confirming where your line actually runs and what your city’s building department requires for setbacks and height. Most cities require a permit for a fence above a certain height or for any fence near an easement, so we check before we quote rather than after.
- 2
Site and soil assessment. The installers walk the full run, note low spots where water collects, check for irrigation lines, drainage easements, and buried utilities, and confirm the ground conditions that determine post depth. This is the step that keeps a fence standing.
- 3
Material and layout decision. You choose the material and the fence line, and we lay the run out physically so you can see where the posts will land, where the gates go, and how the fence meets the house or an existing structure. Brand and profile choices get settled here.
- 4
Installation with set footings. Posts go in first with concrete footings set to depth, followed by rails, panels, and gates. We check plumb and line as we go and confirm gate swing and latch before calling the run finished.
- 5
Final walkthrough and cleanup. We walk the fence line with you, demonstrate the gates, and remove all material and debris. You get a final look at the whole run before we consider the job closed.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Fence Installation Cost in Kendall?
A typical vinyl fence installation in Kendall is estimated at $3,500 – $9,000 depending on linear footage, height, and gate count. Aluminum fencing typically runs $4,000 – $10,000, driven by grade, picket spacing, and how many gates the run needs. Wood fencing and chain link sit at different points depending on whether you’re replacing a full run or reusing sound posts.
Several factors move the number. Total linear footage is the biggest driver, followed by height (a 6-foot privacy run uses more material and deeper posts than a 4-foot yard fence), gate count and hardware, and whether the ground requires extra work for drainage or an easement crossing. Removing an old fence adds labor. If your property has a canal-adjacent section or a utility easement, that affects where posts can go and sometimes what footings are allowed.

To avoid overpaying, get a written, line-item estimate that separates materials, labor, removal, and any permit fees, and make sure it states the post depth and footing. A quote that only gives one lump sum leaves the most important part unspecified.
| Service | Typical Estimated Range |
|---|---|
| Vinyl Fence Installation | $3,500 – $9,000 |
| Aluminum Fence Installation | $4,000 – $10,000 |
Every estimate we provide is free, itemized, and fixed. The written estimate sets the final price, and there are no change orders once work begins. Call (888) 300-8968 for an exact quote.
Fence Installation Near Kendall – Our Service Area
We work with homeowners across Kendall and the surrounding communities, including Richmond Heights, The Crossings, Palmetto Estates, Three Lakes, Westwood Lakes, Kendale Lakes, West Perrine, Country Walk, The Hammocks, Kendall West, and South Miami Heights. If you’re comparing options nearby, our fence installation in Richmond Heights follows the same process, and so does our fence installation in The Crossings. Scheduling depends on the size of the run and material lead time. Call and we’ll give you the earliest opening. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Serving Kendall, FL – Our Local Coverage Area
We serve Kendall and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Fence Installation in Kendall

Fence installation is the process of setting posts, hanging panels or fabric, and fitting gates to enclose or divide a property line. It includes confirming the property line, checking setbacks and permits, setting footings to the right depth, and installing the material you choose. For projects that also touch the front of the home, our fence installation pairs well with a coordinated exterior plan. Call (888) 300-8968 to talk through your run.
Most residential fence runs take one to three days once installation starts, depending on footage, material, and gate count. A short chain link or vinyl run can finish in a day, while a long aluminum or iron installation with multiple gates runs longer. Permit approval and material lead time add to the schedule before work begins, so we give you a realistic window in the written estimate. Call (888) 300-8968 to schedule yours.
Typical estimated pricing in Kendall is $3,500 – $9,000 for vinyl and $4,000 – $10,000 for aluminum, with wood and chain link quoting by footage. The final figure depends on linear footage, height, gate count, and removal of any existing fence. The written estimate sets the final price, so the quote you sign is what you pay. Call (888) 300-8968 for a free estimate.
Yes. We install Master Halco vinyl and ornamental systems and Ameristar aluminum and steel fencing, and we work with other quality lines as well. Brand choice should follow the job: privacy runs, side-yard visibility, gate weight, and the coating that holds up in your conditions. We’ll walk you through the options and quote the material that fits. Call (888) 300-8968 to discuss brands.
Same-day installation isn’t typical for a new fence because material, permits, and a site check come first, but we can often assess and schedule quickly. We answer 24/7. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (888) 300-8968 and we’ll give you the earliest available date.
Yes, our fence installation includes a workmanship warranty on the installation itself, separate from any manufacturer’s warranty on the material. Warranty terms are confirmed in writing as part of your estimate so there’s no ambiguity. If a post or gate issue comes up after the job, call us and we’ll address it. Call (888) 300-8968 for details.
Clear the fence line of furniture, planters, and anything you want to keep, and mark any irrigation heads or buried lines you know about. If pets or children need to be kept away from the work area, plan for that on install day. We’ll confirm access and gate locations with you before we start, so walk the line with the installer when they arrive. Call (888) 300-8968 to schedule.
Schedule Your Fence Installation Service in Kendall Today
One contractor, every trade. Fence installation in Kendall is one of the seven core services we handle, alongside driveway and paver work, windows and doors, roofing, and interior remodeling. Your estimate is free, itemized, and fixed, with a written line-item quote and a workmanship warranty that ends in writing before you sign. Call (888) 300-8968. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Kendall Construction Co.












